Request a demo
GeotechnicalBeta

Geotechware covers the geotechnical work on a project: axial and lateral pile design, drivability, shallow foundations, geotechnical foundation testing, and instrumentation and monitoring. Calculations and reports follow current FHWA, AASHTO, FDOT and ASTM procedures.

Silty sand fillMedium dense sandStiff sandy clayWeathered rock (IGM)Boring B-401020304050607080ftSPT N0204060SPT N (blows/ft)Axial resistance with depth01,0002,0003,0004,000Resistance (kips)Factored loadSide, nominalBase, nominalTotal, nominalTotal, factoredLoad-settlement at 70 ft0.00.40.81.21.602,0004,000Load (kips)in.Davisson 3,987 kipsDavisson offsetPL/AE48 in. drilled shaft, 70 ftNominal resistance3,987 kipsFactored resistance2,070 kipsFactored load1,850 kipsDemand/capacity0.89

Geotechware modules

Site data, foundation and earthwork design, foundation load and integrity testing, and geotechnical instrumentation. Open a module to see its scope and standards.

Data

Site data

  • EasyImport Soil ProfilesBoring logs read automatically or traced by hand into the project borings

    Reads FDOT Report of Core Borings, gINT and scanned boring logs into the project borings, and traces plotted SPT N values and CPT soundings by hand where a log cannot be read. Every boring is checked against the sheet, with strata, SPT blow counts, laboratory values and the header, before it is saved.

    Standards
    ASTM D1586, ASTM D5778, ASTM D2487
    Uses
    Boring log PDFs, scans and plotted logs
    Provides
    Project borings with strata and SPT values

Design

Deep foundations

  • Axial Pile CapacityDriven piles, drilled shafts, auger cast piles

    Computes nominal and factored axial resistance of driven piles, drilled shafts and auger cast piles from the project borings. Produces side and tip resistance with depth, required embedment for the design loads, and the resistance factors applied.

    Standards
    AASHTO LRFD Bridge Design Specifications, FHWA GEC 12, FHWA GEC 10, FHWA GEC 8
    Uses
    Project borings, foundation loads
    Provides
    Pile length and factored axial resistance
  • Lateral Pile AnalysisNonlinear p-y analysis, single piles and groups

    Computes lateral response of single piles and pile groups using nonlinear p-y curves generated from the soil layers. Produces deflection, rotation, bending moment and shear with depth, and group reduction factors for the applied loads and head fixity.

    Standards
    AASHTO LRFD Bridge Design Specifications
    Uses
    Project borings, pile section, lateral loads
    Provides
    Pile deflection, moment and shear profiles
  • Pile DrivabilityWave equation analysis, hammer selection

    Performs wave equation analysis of pile driving for candidate hammers and pile sections. Produces bearing graphs, driving stresses compared with allowable limits, and blow count versus depth, used to select a hammer and set driving criteria.

    Standards
    AASHTO LRFD Bridge Design Specifications, FHWA GEC 12
    Uses
    Project borings, pile section, required resistance
    Provides
    Hammer selection and driving criteria

Shallow foundations and platforms

  • Shallow FoundationsBearing capacity, Schmertmann settlement

    Computes bearing resistance of spread footings and mats from the project borings and footing geometry. Estimates immediate settlement in granular soils by the Schmertmann method and reports factored bearing resistance and settlement for each load case.

    Standards
    AASHTO LRFD Bridge Design Specifications, FHWA GEC 6
    Uses
    Project borings, footing geometry, loads
    Provides
    Factored bearing resistance and settlement
  • Crane Pads and Working PlatformsBearing and platform thicknessComing soon

    Checks bearing of the subgrade under crane outrigger pads and tracked plant loads. Computes the required granular platform thickness for the given equipment loads and subgrade strength, and reports bearing resistance for each load case.

    Standards
    No single governing document
    Uses
    Project borings, equipment loads
    Provides
    Platform thickness and bearing check

Walls and slopes

  • Retaining WallsEarth pressure, sliding and overturning

    Computes active, at-rest and passive earth pressures on retaining walls, including surcharge and water pressure. Checks sliding, overturning and bearing resistance for each load combination and reports the capacity to demand ratios and wall base dimensions.

    Standards
    AASHTO LRFD Bridge Design Specifications
    Uses
    Project borings, wall geometry, surcharges
    Provides
    Wall stability checks and base dimensions
  • Earth RetentionGround anchors, soil nail walls

    Designs ground anchor and soil nail walls from the project borings and excavation geometry. Computes anchor or nail loads, bond lengths, spacing and facing demands, and checks pullout, tendon or bar tensile resistance and external stability.

    Standards
    FHWA GEC 4, FHWA GEC 7, PTI DC35.1, AASHTO LRFD Bridge Design Specifications
    Uses
    Project borings, excavation geometry, surcharges
    Provides
    Anchor and nail layout and loads
  • Slope StabilityLimit equilibrium slopes and global stability of walls

    Computes factors of safety for embankment and cut slopes by limit equilibrium methods, searching circular and noncircular slip surfaces. Checks global stability of walls and reports the critical surface and minimum factor of safety for each loading condition.

    Standards
    AASHTO LRFD Bridge Design Specifications
    Uses
    Project borings, ground surface, wall geometry
    Provides
    Critical slip surface and factor of safety

Ground and environmental

  • Seismic Site ClassASCE 7 site class, lateral spread, post-liquefaction settlement

    Determines seismic site class from SPT, shear wave velocity or undrained shear strength in the upper 100 feet. Estimates lateral spread displacement and post-liquefaction settlement and reports the site class and design ground motion parameters.

    Standards
    ASCE 7, AASHTO Guide Specifications for LRFD Seismic Bridge Design, FHWA GEC 3
    Uses
    Project borings, site location
    Provides
    Site class and seismic design parameters
  • LiquefactionSPT and CPT triggering, settlement

    Evaluates liquefaction triggering from SPT and CPT data for the design earthquake magnitude and peak ground acceleration. Produces factor of safety against liquefaction with depth and estimated post-liquefaction volumetric strain and ground surface settlement.

    Standards
    FHWA GEC 3, ASTM D1586, ASTM D5778
    Uses
    Project borings, CPT profiles, seismic parameters
    Provides
    Liquefaction factor of safety and settlement
  • Ground ImprovementWick drains, aggregate piers, dewatering and seepage

    Designs wick drain spacing for consolidation time, aggregate pier support for settlement and bearing, and dewatering systems for excavations. Computes degree of consolidation with time, improved settlement, seepage flows and drawdown for the given site conditions.

    Standards
    FHWA GEC 13
    Uses
    Project borings, fill loads, groundwater levels
    Provides
    Drain spacing, pier layout, dewatering flows
  • Pavement DesignFlexible and rigid pavements, subgrade

    Designs flexible and rigid pavement sections from traffic loading and subgrade support values. Computes required structural number or slab thickness and layer thicknesses, and reports subgrade resilient modulus derived from borings or laboratory results.

    Standards
    AASHTO Guide for Design of Pavement Structures, FDOT Flexible Pavement Design Manual, FDOT Rigid Pavement Design Manual
    Uses
    Project borings, traffic data, lab results
    Provides
    Pavement layer thicknesses
  • EnvironmentalSite assessment, screening, vapor and remediation tools

    Organizes environmental site assessment records, compares sample results with screening levels, and evaluates vapor encroachment. Produces tabulated exceedances, screening summaries and remediation quantity estimates for the areas and media sampled on the project.

    Standards
    ASTM E1527, ASTM E1903, ASTM E2600
    Uses
    Project site, sample results
    Provides
    Screening exceedances and remediation quantities

Testing

Load tests

  • Bi-Directional Static Load TestCell load test monitoring, load-displacement and unit resistance analysis

    Records embedded cell pressure, displacement and strain gauge readings during bi-directional static load tests. Produces load-displacement curves above and below the cell, unit side and end resistance by zone, and an equivalent top-down load-settlement curve.

    Standards
    ASTM D8169
    Uses
    Shaft design, project borings
    Provides
    Measured resistance and equivalent top-load curve
  • Bi-Directional Layout OptimizerCell level, jack size and count, gauge and tube layout from the design

    Selects the cell level from the design side and end resistance so the test loads both segments. Sizes jack capacity and count, and lays out strain gauge levels, telltales and access tubes for the test shaft.

    Standards
    ASTM D8169
    Uses
    Shaft design, project borings
    Provides
    Cell level, jack size, instrument layout
  • 3D Shaft ModelShaft, cage, cell assembly and instruments in 3D from design, caliper or thermal data

    Builds a three-dimensional model of the shaft, reinforcing cage, cell assembly and instruments from the design drawings. Updates the shaft shape from caliper or thermal integrity data and reports cover, diameter and volume with depth.

    Standards
    ASTM D7949, FHWA GEC 10
    Uses
    Shaft design, caliper and thermal data
    Provides
    Shaft geometry and cover with depth
  • Top-Down Static Load TestCompression and tension load-settlement interpretation

    Records load and displacement readings from compression and tension static load tests. Interprets the load-settlement curve by standard failure criteria, reports measured capacity, and compares the result with the design resistance for the tested pile or shaft.

    Standards
    ASTM D1143, ASTM D3689
    Uses
    Pile design, project borings
    Provides
    Measured capacity versus design resistance
  • Lateral Load TestLoad-deflection analysis and p-y calibration

    Records lateral load and deflection readings from pile lateral load tests. Produces load-deflection curves and calibrates p-y curve parameters so the analysis matches the measured response, for use in the lateral pile analysis.

    Standards
    ASTM D3966
    Uses
    Lateral pile analysis, project borings
    Provides
    Measured deflections and calibrated p-y parameters
  • Dynamic Load Test ReportingHigh-strain test results and capacity reporting

    Compiles high-strain dynamic test results, including driving stresses, transferred energy, integrity and signal matching capacity. Produces tabulated results by pile and blow, and compares measured capacity with the required driving resistance.

    Standards
    ASTM D4945
    Uses
    Pile design, driving records
    Provides
    Measured capacity and driving stresses

Integrity tests

  • Thermal Integrity ProfilingShaft shape, cover and anomaly evaluationComing soon

    Evaluates thermal integrity profiling data from drilled shafts and auger cast piles. Computes effective shaft radius and cage cover with depth from measured temperatures and concrete volume, and flags anomalies for evaluation and reporting.

    Standards
    ASTM D7949
    Uses
    Shaft design, pour records
    Provides
    Shaft radius, cover and anomaly flags
  • Crosshole Sonic LoggingFirst arrival and energy anomaly evaluationComing soon

    Evaluates crosshole sonic logging data between access tube pairs in drilled shafts. Computes first arrival time and relative energy with depth, identifies anomalies against delay and energy reduction criteria, and reports anomaly zones by tube pair.

    Standards
    ASTM D6760
    Uses
    Shaft design, tube layout
    Provides
    Anomaly zones by tube pair

Monitoring

Instrumentation

  • PiezometersPore pressure readings and dissipation trendsComing soon

    Records pore pressure readings from vibrating wire and standpipe piezometers. Produces pore pressure versus time plots, excess pore pressure dissipation trends and estimated degree of consolidation, for comparison with the design assumptions for embankment and fill loading.

    Standards
    No single governing document
    Uses
    Instrument locations, fill records
    Provides
    Pore pressure and dissipation trends
  • Groundwater MonitoringWater level records from observation wellsComing soon

    Records water level readings from observation wells and monitoring wells across the site. Produces water level elevation versus time plots and seasonal high and low levels, for comparison with the design groundwater elevations used in analysis.

    Standards
    ASTM D5092
    Uses
    Well locations, project borings
    Provides
    Measured groundwater elevations
  • Settlement PlatesFill settlement with time and consolidationComing soon

    Records settlement plate elevations under fills and embankments over time. Produces settlement versus time and fill height plots, fits consolidation curves to estimate end-of-primary settlement, and compares measured settlement with the design prediction.

    Standards
    No single governing document
    Uses
    Plate locations, fill records, design settlement
    Provides
    Measured settlement and consolidation estimates
  • InclinometersLateral deformation profiles and displacement ratesComing soon

    Reduces probe inclinometer readings into cumulative lateral deformation profiles with depth. Computes displacement rates, identifies shear zones, and compares movements against alert and action thresholds for slopes, walls and excavations.

    Standards
    ASTM D6230
    Uses
    Instrument locations, wall and slope designs
    Provides
    Lateral deformation profiles and rates
  • ExtensometersVertical deformation with depth over timeComing soon

    Records borehole and magnetic extensometer readings at anchors along the borehole. Produces vertical deformation with depth over time, separates compression by layer, and compares measured layer compression with the settlement predicted in design.

    Standards
    No single governing document
    Uses
    Instrument locations, design settlement
    Provides
    Vertical deformation by layer
  • Remote Vibration MonitoringPeak particle velocity against threshold limitsComing soon

    Records peak particle velocity and frequency from seismographs near construction activity. Compares readings with the project threshold limits, flags exceedances by time and location, and produces event summaries for structures in the monitoring area.

    Standards
    USBM RI 8507
    Uses
    Monitoring locations, threshold limits
    Provides
    Vibration readings and exceedances

Geotechware beta program

FHWA · AASHTO LRFD · ASTM · ASCE 7

Geotechware beta workflow1Set upSoil profile, CPT, SPT, boring logs2Field testsBi-directional, static, lateral, dynamic3Deep foundationsAxial, lateral, groups, drivability4Shallow, walls, slopesBearing, walls, anchors, stability5Report40 report types, draft until sealed
Program map with sample data. Each step opens the matching screens; results carry forward to the report.
  1. Set up the projectProject type, foundation system, code basis, soil profile from the boring logs, and CPT and SPT data.
  2. Run the field testsBi-directional layout optimizer and 3D shaft model, then bi-directional, top-down static, lateral and dynamic load tests, with strain data processing and live monitoring.
  3. Design the deep foundationsAxial capacity by method set, capacity with depth, lateral p-y analysis, groups, pile caps, drivability and downdrag.
  4. Design shallow foundations, walls and slopesBearing and settlement, retaining walls, anchors and soil nails, slope and global stability, ground improvement and pavements.
  5. Issue the reportAfter the engineer's review, 40 report types are generated with figures, tables and calculations, marked draft until sealed.

In every Geotechware module

Common tools across design, testing and monitoring, from data entry to the issued report.

EasyImport™ Soil ProfilesImport boring logs as PDF or scanned images. Strata, SPT N values, groundwater levels and laboratory results are read into the soil profile for review, with no retyping.SPT, CPT, lab data
Calibrated DesignLoad test results are back-calculated against the design model for the same site. Geotechware then recommends a calibrated, more efficient design using the measured unit side and base resistance, t-z and q-z curves, and p-y multipliers.Load test to design
Documented MethodsEach analysis shows its assumptions, equations, citations and calculation method, with references to the governing standard and the latest published research.FHWA, AASHTO, ASTM, FDOT
EasyReport™ DeliverablesFigures, tables, calculation sheets and CAD drawings are generated from the analysis in a few clicks, on your company template.PDF, DOCX, CAD

Bi-directional static load test, beta

Sign in to the beta module

No access code? Request beta access

Questions about Geotechware?